Refrigerant Plant Room Monitoring
Refrigerant gases are used to provide a means of cooling the evaporators in freezers and air conditioning for plant rooms and chiller plants. Historically CFC refrigerant gases such as R11, R12 and R22 have been used. CFC’s are ozone depleting gases and are now being phased out and replaced by ozone friendly gases such as R134, R407 and R410.
Why is there a need to detect them?
- All these gases are toxic at relatively low levels. Prolonged exposure to these gases is hazardous and results in serious health risks. GDA sensors can detect these gases at very low levels, in order to prevent this hazard becoming a danger to life.
- Air conditioning systems and chillers that are leaking their refrigerant gases are not performing to maximum efficiency. The major use of refrigerant gases is in the re charging of these systems. If leaks are detected early the problem can be alleviated much quicker, saving costs on replacement gas, co maintenance and protecting the environment.
- Gas detection at low levels (part per million) will give an early warning of leakage, therefore safeguarding life and maintaining the efficiency of the plant.
Gas Detection Australia has a range of ultra-low level refrigerant gas leak detection systems specifically developed to prevent the expensive results of refrigerant gas leaks for R22, R123, R134a, R404, R407, R410, R514a, R1234yf and many others.
Meets the requirements of AS/NZS 5149.3:2016 and ISO 5149-3:2014
Designed, Manufactured and Supported in Australia.
GDA 2526 : Ammonia Gas Sensor
The GDA 2526 Ammonia (NH₃) gas sensor is a 2 wire 4-20 mA Loop Powered device. It has an electrochemical sensing unit which is temperature compensated and easily replaceable.
Designed, manufactured and supported locally in Australia.
GDA 2626 : Ammonia Gas Sensor with Voltage Output
The GDA 2626 Ammonia gas sensor is a further enhancement of the GDA 2526 Ammonia gas sensor that allows AC and DC operation. It has an electrochemical gas sensing unit which is temperature compensated and easily replaceable.
Designed, manufactured and supported locally in Australia.
GDA 3100 : Refrigerant Gas Detector
The GDA 3100 Refrigerant Gas Detector uses the latest in NDIR techniques for detecting a wide range of refrigerant gases and is immune from cross sensitivity to other gases. In addition it is immune to changes in humidity and temperature with a longer lifespan then standard semiconductor sensors.
Designed, manufactured and supported locally in Australia.
GDA 3160 : Flush Mount Refrigerant Gas Detector
The GDA 3160 is a low profile wall mounted refrigerant detector for use in offices and laboratories where a gas sensor needs to appear non obtrusive. The sensor uses the lastest in NDIR techniques for detecting a wide range of refrigerant gases and is therefore immune from cross sensitivity to other gases.
Designed, manufactured and supported locally in Australia.
GDA 4350 : Carbon Dioxide Gas Sensor
The GDA 4350 is a 3 wire Non Dispersive Infra red (NDIR) Carbon Dioxide (CO₂) sensor. It gives a 4-20 mA, 0-20 mA, 0-5 V or 0-10 V o/p over the range of the sensor. Low Temperature version available.
Designed, manufactured and supported locally in Australia.
GDA 4360 : Flush Carbon Dioxide Gas Sensor
The GDA 4360 is a 3 wire 4-20 mA Non Dispersive Infra red (NDIR) Carbon Dioxide (CO₂) Sensor. It gives a 4-20 mA o/p over the range of the sensor. Designed for applications where low profile intrusion into a room space is required.
Designed, manufactured and supported locally in Australia.
GDA 4350 PUMP : Carbon Dioxide Gas Sampling System
The GDA 4350 Pump is designed to be used where diffusion sensors are impractical due to environmental or wash down requirements. An advanced 3 wire Non Dispersive Infra red (NDIR) Carbon Dioxide sensor giving a 4-20 mA, 0-20 mA, 0-5 V or 0-10 V o/p over the range of the sensor. Low Temperature version available.
Designed, manufactured and supported locally in Australia.
GDA 7228 : Flush Mount Oxygen Gas Sensor
The GDA7228 Flush Mount Oxygen gas sensor is a 2 wire 4-20 mA Loop Powered device with a range of 0-25% vol Oxygen.
Designed, manufactured and supported locally in Australia.
GDA 40126 : Flammable Gas Detection Controller
The GDA 40126 Gas Detection Controller is a standalone gas detector unit with inbuilt display, sounder, flasher, relays and alarm driver. Available for Flammable gases such as LNG, LPG, Propane, Hydrogen, Acetylene, Solvents, and other flammable vapours. Designed to be used in Non-hazardous areas with the GDA 2500 series easily replaceable sensor modules.
Designed, manufactured and supported locally in Australia.
GDA 40127 : Carbon Dioxide Gas Detection Controller
The GDA 40127 Carbon Dioxide Gas Detection Controller is a standalone gas detector unit with inbuilt display, sounder, flasher, relays and alarm driver using an non dispersive infra red sensor.
Designed, manufactured and supported locally in Australia.
GDA 4020 : Two Channel Gas Detection Controller
The GDA 4020 control unit has 2 x 4-20 mA i/p with 3 associated programmable relay alarm levels per sensor. There is an independent fault relay. There are 3 x analog o/p’s which can be configured for either channel as 4-20 mA, 0-20 mA, 0-5 V or 0-10 V. The controller has an isolated RS485 o/p which can be configured to drive modbus or an interface to the M2001 mimic panel. All configurations are carried out via the front panel push buttons. The unit requires 24 VDC.
Designed, manufactured and supported locally in Australia.
GDA 4080 : 8 Channel Gas Detection Controller
The GDA 4080 Gas Detection Controller is designed to be to take up to 8x 4-20 mA sensor inputs and display the gas readings of the individual sensors. The multi-colour display will indicate the alarm status, levels and faults.
Designed, manufactured and supported locally in Australia.
GDA 2400 : Multiplexed 8 Channel Gas Detection Controller
The GDA 2400 control unit caters for up to 8 GDA Sensors. The controller selects the highest reading from the sensors and displays the highest reading and is used when all the gas sensors are the same type. It is particularly useful in Periphery monitoring and Car park ventilation control.
Designed, manufactured and supported locally in Australia.
M2001 : Flush Mount Mimic Panel
The M2001 is a low profile flush wall mounted mimic panel. These units are used on multi entry rooms so that users may view the gas levels and alarm status of each entry point for entering the room, used in conjunction with the GDA 4020, GDA 2400 or GDA 4500 control unit.
Designed, manufactured and supported locally in Australia.
GDA 74001 : Extended Mimic Panel
The GDA 74001 is a low profile flush wall mounted mimic panel. These units are used on multi entry rooms so that users may view the gas levels and alarm status of each entry point for entering the room The 74001 is used in conjunction with the GDA 4080 control unit.
Designed, manufactured and supported locally in Australia.
GDA 74002 : Extended Mimic Large Character Display
The GDA 74002 is a Extended Mimic Large Character Display . These are designed so that users may view the gas level and alarm status clearly from any point. The colour of the LED back light changes depending on the alarm state of the GDA 4080 control unit.
Designed, manufactured and supported locally in Australia.
MS001 : Flush Mount Mute Switch
The MS001 uses one of the alarm SPCO relays from the GDA 4020, GDA 4011, or GDA 2400 to drive the AVR-20R/YM sounder- flasher. The sounder- flasher can be muted by incorporating the MS001 into the o/p switched 24 VDC from the control panel. The sounder will sound when a gas alarm occurs and continue sounding until either the alarm level falls below its threshold value or the MS001 button is pressed. The Mute function automatically resets when the alarm condition terminates.
Designed, manufactured and supported locally in Australia.
AVR 20 : Alarm Flasher and Sounder
This sounder/flashers operates at 24VDC. The sounder can be permanently disabled so that unit acts as a flasher only. These units are designed for internal use. These are available in Red or Amber.
Signage : Gas Emergency Information Signs/Gas Alarm Signage
Gas Emergency Information Signs / Gas Alarm Signage
