Carbon Dioxide (CO₂) Gas
Carbon dioxide (CO₂) is a colorless gas with a density about 60% higher than that of dry air. Carbon dioxide is odorless at normally encountered concentrations, however, at high concentrations, it has a sharp and acidic odor.
It is a versatile industrial material, used, for example, as an inert gas in welding and fire extinguishers, as a pressurizing gas in air guns and oil recovery, and as a supercritical fluid solvent in decaffeination of coffee and supercritical drying. It is added to drinking water and carbonated beverages including beer and sparkling wine to add effervescence. The frozen solid form of CO₂, known as dry ice is used as a refrigerant and as an abrasive in dry-ice blasting.
Safe Work Australia Exposure Standards
8 Hour Time Weighted Average |
5,000 ppm |
15 Minute Short Term Exposure Limit |
30,000 ppm |
More Infomation © Commonwealth of Australia 2018
GDA 4350: Carbon Dioxide Gas Sensor
The GDA 4350 is a 3 wire Non Dispersive Infra red (NDIR) Carbon Dioxide (CO₂) sensor. It gives a 4-20 mA, 0-20 mA, 0-5 V or 0-10 V o/p over the range of the sensor. Low Temperature version available.
Designed, manufactured and supported locally in Australia.
GDA 4360: Flush Carbon Dioxide Gas Sensor
The GDA 4360 is a 3 wire 4-20 mA Non Dispersive Infra red (NDIR) Carbon Dioxide (CO₂) Sensor. It gives a 4-20 mA o/p over the range of the sensor. Designed for applications where low profile intrusion into a room space is required.
Designed, manufactured and supported locally in Australia.
GDA 40127: Carbon Dioxide Gas Detection Controller
The GDA 40127 Carbon Dioxide Gas Detection Controller is a standalone gas detector unit with inbuilt display, sounder, flasher, relays and alarm driver using an non dispersive infra red sensor.
Designed, manufactured and supported locally in Australia.
SENKO SI-100: Explosion Proof Gas Detector
SI-100 is an IEC Ex fixed gas detector installed where potential gas hazard occur to measure and monitor oxygen, toxic gas and combustible gas. Through the LCD display the SI-100 shows the concentration of gases present and the status of the unit in real time. It can be connected to a controller with a standard 4-20mA analog output communication. With magnetic buttons a Hot Work permit not required for calibration with no need to open the device.
SENKO SI-100C: Explosion Proof Gas Sensor
SI-100C is a IEC Ex explosion proof gas sensor ready to installed hazardous and non-hazardous areas to prevent gas hazards caused oxygen depletion, toxic gas or combustible gas. Available to detect over 25 different gas types, see Ordering Information for details.
GDA 3000: Explosion Proof (IEC Ex) Flammable / Carbon Dioxide Gas Detector
This Infra red sensor is certified for use in Zone 1 Hazardous areas within Australia.
FULLY TECHNICALLY SUPPORTED by GAS DETECTION AUSTRALIA.
GDA 4500: Single Point Gas Sampling System
The GDA 4500 is designed to be used where sensors are placed in areas that are difficult to gain access such as pits and elevated areas.
Designed, manufactured and supported locally in Australia.
GDA 4508: Multi Point Sampling System
The GD 4508/16 is a 1 to 16 point gas sampling system for use in commercial buildings to control fresh air make up in rooms relative to external fresh air. Available for: Carbon Monoxide (CO), Oxygen (O₂) or Carbon Dioxide (CO2).
Designed, manufactured and supported locally in Australia.
GDA 5000Tx: Sampling Toxic Gas Detector
Designed to be used where areas that are difficult to gain access due to distance or toxic environment. As well as to detect greater ranges of toxic gases using advanced Pyrolyzer technology converting electrochemically inactive gases to easily detected gases.