When gas is piped into rooms for experimental purposes such as CO2, CO, or Natural Gas .The Gas Detection Australia range of sensors can be used to detect any leaks that may present a danger to health or explosion.
The GDA 2528 Oxygen gas sensor is a 2 wire 4-20 mA Loop Powered device with a range of 0-25% vol Oxygen. It has an electrochemical gas sensing unit which is temperature compensated and easily replaceable.
Designed, manufactured and supported locally in Australia.
The GDA 3160 is a low profile wall mounted refrigerant detector for use in offices and laboratories where a gas sensor needs to appear non obtrusive. The sensor uses the lastest in NDIR techniques for detecting a wide range of refrigerant gases and is therefore immune from cross sensitivity to other gases.
Designed, manufactured and supported locally in Australia.
The GDA 4350 is a 3 wire Non Dispersive Infra red (NDIR) Carbon Dioxide (CO₂) sensor. It gives a 4-20 mA, 0-20 mA, 0-5 V or 0-10 V o/p over the range of the sensor. Low Temperature version available.
Designed, manufactured and supported locally in Australia.
The GDA 4360 is a 3 wire 4-20 mA Non Dispersive Infra red (NDIR) Carbon Dioxide (CO₂) Sensor. It gives a 4-20 mA o/p over the range of the sensor. Designed for applications where low profile intrusion into a room space is required.
Designed, manufactured and supported locally in Australia.
The GDA7228 Flush Mount Oxygen gas sensor is a 2 wire 4-20 mA Loop Powered device with a range of 0-25% vol Oxygen.
Designed, manufactured and supported locally in Australia.
The GDA 40125 Gas Detection Controller is a standalone gas detector unit with inbuilt display, sounder, flasher, relays and alarm driver. Available in the full range of GDA 2500 series electrochemical sensors which are temperature compensated and easily replaceable.
Designed, manufactured and supported locally in Australia.
SI-100C is a IEC Ex explosion proof gas sensor ready to installed hazardous and non-hazardous areas to prevent gas hazards caused oxygen depletion, toxic gas or combustible gas. Available to detect over 25 different gas types, see Ordering Information for details.
Locally Technically Supported by Gas Detection Australia
The GDA 2000Ex Flammable Gas Detector is certified for use in Zone 1 Hazardous areas within Australia.
Locally Technically Supported by Gas Detection Australia
GDA 2000Tx Explosion Proof (IEC Ex) Toxic and Oxygen Gas Detector is certified for use in Zone 1 Hazardous areas within Australia.
Locally Technically Supported by Gas Detection Australia
This Infra red sensor is certified for use in Zone 1 Hazardous areas within Australia.
Locally Technically Supported by Gas Detection Australia
Designed to be used where areas that are difficult to gain access due to distance or toxic environment. As well as to detect greater ranges of toxic gases using advanced Pyrolyzer technology converting electrochemically inactive gases to easily detected gases.
The GDA 4020 control unit has 2 x 4-20 mA i/p with 3 associated programmable relay alarm levels per sensor. There is an independent fault relay. There are 3 x analog o/p’s which can be configured for either channel as 4-20 mA, 0-20 mA, 0-5 V or 0-10 V. The controller has an isolated RS485 o/p which can be configured to drive modbus or an interface to the M2001 mimic panel. All configurations are carried out via the front panel push buttons. The unit requires 24 VDC.
Designed, manufactured and supported locally in Australia.
The GDA 4080 Gas Detection Controller is designed to be to take up to eight sensor inputs and display the gas readings of the individual sensors. The multi-colour display will indicate the alarm status, levels and faults.
Designed, manufactured and supported locally in Australia.
The GDA 2400 control unit caters for up to 8 GDA Sensors. The controller selects the highest reading from the sensors and displays the highest reading and is used when all the gas sensors are the same type. It is particularly useful in perimeter monitoring and car park ventilation control.
Designed, manufactured and supported locally in Australia.
The M2001 is a low profile flush wall mounted mimic panel. These units are used on multi entry rooms so that users may view the gas levels and alarm status of each entry point for entering the room, used in conjunction with the GDA 4020, GDA 2400 or GDA 4500 control unit.
Designed, manufactured and supported locally in Australia.
The GDA 74001 is a low profile flush wall mounted mimic panel. These units are used on multi entry rooms so that users may view the gas levels and alarm status of each entry point for entering the room The 74001 is used in conjunction with the GDA 4080 control unit.
Designed, manufactured and supported locally in Australia.
The GDA 74002 is a Extended Mimic Large Character Display . These are designed so that users may view the gas level and alarm status clearly from any point. The colour of the LED back light changes depending on the alarm state of the GDA 4080 control unit.
Designed, manufactured and supported locally in Australia.
The GDA 4080RD Remote Display is a flush mounted multi-colour display will indicate the alarm status, levels and faults in a remote location from the main GDA 4080 Control Panel
Designed, manufactured and supported locally in Australia.
The GDA Dual Channel Repeater Panel allows for simple replication of the alarm and system status of all GDA gas detection controllers by visual and auditory indicators.
Designed, manufactured and supported locally in Australia.
The MS001 uses one of the alarm relays from a GDA gas detection controller to drive the AVR-20R/YM sounder & flasher. The sounder- flasher can be muted by incorporating the MS001 into the output switched 24 VDC from the control panel.
Designed, manufactured and supported locally in Australia.
This sounder/flashers operates at 24VDC. The sounder can be permanently disabled so that unit acts as a flasher only. These units are designed for internal use. These are available in Red or Amber.
Gas Emergency Information Signs / Gas Alarm Signage